Servo Stabilizers

Servo stabilizer - Single Phase Air Cooled

.

Servo stabilizer Technical Specification

Specification  Single Phase
Capacity 2 KVA - 25 KVA Air Cooled/2 KVA - 25 KVA Oil Cooled
Input  Range 120,140,170,200-270
Output Voltage 230V AC adjustable between 200V-240V
Correction Rate 15V / 20V / 35V / Sec
Protection Over/Under Voltage for Input & Output side, ShortCircult, Overload,   Fuse Protection for Motor & Input
LEDs Indication Input On, Output On, Output Cut Off, Output Low Cut Off, Output High Cut Off, Over Load,
System & Connection  P,N,E
Supply Frequency  50HZ+5%
Output Regulations  +/- 1% (No Load to Full Load)
Insulation  Class "B","F","H"
Metering 3-7 Segment Leds Display for Input/ Output Voltage Load Current, Over Load Setting, Snaitivity, High/Low cut of voltage, Supply Frequency
Ambient Teemperature 45"C Max, Relative Humidity upto 90%
Output waveform Ture Reproduction Of Input
Overload Capacity 120% Maximum
Type of Cooling Oil / Air
Mode of System Fully automatic
Output Control Relay/Contactor to  Auto on (3 Sec to 3 Min).
Servo motor drive AC. Synchronous stepper motor
Input/Output Connection Up to 3 KVA Plug & Top Above 3 KVA Input Output Terminal
Efficiency More than 98%
System Construction As Per IS : 9815-1994
Non-Standard Input and Output ranges also available as per customer requirement*
Salient Features
  • Special designs of Transfomer to minimize losses (negligible no load current). More Than 98% effcietly
  • 3-7 Segment LEDs Display For Input /output Voltage,Current,Frequency
  • Bult-in spike and surge protector
  • All fuctions and parameters are fully software programmable for constant output voltage even with distorted Input from DG set
  • Bult- in Protection Against Under/Over Voltage (Input/Ouput),Short circuit
  • Sesing circuit is isolated from input
  • All electronic assemblies tested on full load for 48 hours to minimize failures
  • Higher Overload capabilities for high starting and regenerating currents repeated frequently in CNC / Textile machines
  • Auto and manual operation facility
  • No hunting, No oscillation, No noise generations
  • All components sourced from reputed manufactures
  • Rugged AC synchronise motor with instant Stop / Start Characteristies
  • No effect of power factor
  • In built By-pass Switch upto 15 KVA

Stabilizer - Three Phase Air Cooled

.

Servo stabilizer Technical Specification

Specification Three Phase
Capacity 3 KVA -1500 KVA Oil Cooled / 3 KVA -75 KVA Air Cooled
Input  Range 220V / 240V / 300V / 340V / 360V/380V
Output Voltage 400V AC adjustable between 380V-415V
Correction Rate 25V / 35V / 60V / Sec Phase To Phase
Protection Over/Under Voltage/ ShortCircult/ Overload/ Single Phasing/Phase reverse, Fuse Protection for Motor & Input
LEDs Indication Input On, Output On, Output Cut Off, Output High Cut Off,Output Low Cutoff, Over Load, Single Phase, Phase Reverse, Output Cut-Off
System & Connection  Unbalances 4 Wires (RYB&N), Star Connected with earth
Supply Frequency 50HZ+5%
Output Regulations  1% (No Load To Full Load)
Insulation  Class "B","F","H"
Metering 3-7 Segment Leds Display for Input/ Output Voltage Load Current, Over Load Setting, Sensitivity, High/Low cut of voltage, Supply Frequency
Ambient Teemperature 45"C Max, Relative Humidity upto 90%
Output waveform Ture Reproduction Of Input
Overload Capacity 120% Maximum
Type of Cooling Oil / Air
Mode of System Fully automatic
Output Control Contactor Through Manual feather touch button. Optional for automatic (7 Sec to 3 Min)
Servo motor drive AC. Synchronous stepper motor
Input/Output Cabling Up to 6KVA Connectors, Above 9 KVA Hylom with bold nut, Above 50KVA Hylam with AL Flat Input Output Cable glands provision and Double Earth Connecting Provision Provided
Efficiency   More then 98%
System Construction As Per IS : 9815-1994
Non-Standard Input and Output ranges also available as per customer requirement*
Salient Features
  • Special designs of Transfomer to minimize losses (negligible no load current). More Than 98% effcietly 3-7 Segment LEDs Display
  • Bult-in spike and surge protector
  • All fuctions and parameters are fully software programmable for constant output voltage even with distorted Input from DG set
  • Bult- in Protection Against Under/ Over Voltage (Input/Ouput),Short circuit, single phasing & Phase reverse
  • Sesing circuit is isolated from input
  • All electronic assemblies tested on full load for 48 hours to minimize failures
  • Higher Overload capabilities for high starting and regenerating currents repeated frequently in CNC / Textile machines
  • Auto and manual operation facility. No hunting, No oscillation,No noise generations
  • All components sourced from reputed manufactures
  • Rugged AC synchronise motor with instant Stop / Start Characteristies
  • No effect of power factor
  • In built By-pass Switch upto 30 KVA.

Stabilizer - Three Phase Oil Cooled With fin

.

Servo stabilizer Technical Specification

Specification Three Phase
Capacity 75 KVA -1500 KVA Oil Cooled
Input  Range 220V / 240V / 300V / 340V / 360V/380V
Output Voltage 400V AC adjustable between 380V-415V
Correction Rate 25V / 35V / 60V / Sec
Protection Over/Under Voltage/ ShortCircult/ Overload/ Single Phasing/Phase reverse, Fuse Protection for Motor & Input
LEDs Indication Input On, Output On, Output Cut Off, Output High Cut Off,Output Low Cutoff, Over Load, Single Phase, Phase Reverse, Output Cut-Off
System & Connection  Unbalances 4 Wires (RYB&N), Star Connected with earth
Supply Frequency 50HZ+5%
Output Regulations  +/- 1% (No Load & Full Load)
Insulation  Class "B","F"
Metering 3-7 Segment Leds Display for Input/ Output Voltage Load Current, Over Load Setting, Sensitivity, High/Low cut of voltage, Supply Frequency
Ambient Teemperature 45"C Max, Relative Humidity upto 90%
Output waveform Ture Reproduction Of Input
Overload Capacity 120% Maximum
Type of Cooling Oil
Mode of System Fully automatic
Output Control Contactor Through Manual feather touch button. Optional for automatic (7 Sec to 3 Min)
Servo motor drive AC. Synchronous stepper motor
Inout/Output Connection Hylam with AL Flat with Bolt Nut
Efficiency   More then 98%
System Construction As Per IS : 9815-1994
Non-Standard Input and Output ranges also available as per customer requirement*
Salient Features
  • Special designs of Transfomer to minimize losses (negligible no load current). More Than 98% effcietly 3-7 Segment LEDs Display
  • Bult-in spike and surge protector
  • All fuctions and parameters are fully software programmable for constant output voltage even with distorted Input from DG set
  • Bult- in Protection Against Under/ Over Voltage (Ouput),Short circuit, single phasing & Phase reverse
  • Sesing circuit is isolated from input
  • All electronic assemblies tested on full load for 48 hours to minimize failures
  • Higher Overload capabilities for high starting and regenerating currents repeated frequently in CNC / Textile machines
  • Auto and manual operation facility. No hunting, No oscillation,No noise generations
  • All components sourced from reputed manufactures
  • Rugged AC synchronise motor with instant Stop / Start Characteristies
  • No effect of power factor
  • In built By-pass Switch upto 30 KVA

Stabilizer - Three Phase Oil Cooled With Tube

.

Servo stabilizer Technical Specification

Specification Three Phase
Capacity 3 KVA - 75 KVA Oil Cooled
Input  Range 220V / 240V / 300V / 340V / 360V/380V
Output Voltage 400V AC adjustable between 380V-415V
Correction Rate 25V / 35V / 60V / Sec
Protection Over/Under Voltage/ ShortCircult/ Overload/ Single Phasing/Phase reverse, Fuse Protection for Motor & Input
LEDs Indication Input On, Output On, Output Cut Off, Output High Cut Off,Output Low Cutoff, Over Load, Single Phase, Phase Reverse, Output Cut-Off
System & Connection  Unbalances 4 Wires (RYB&N), Star Connected with earth
Supply Frequency 50HZ+5%
Output Regulations  1% (No Load & Full Load)
Insulation  Class "B","F"
Metering 3-7 Segment Leds Display for Input/ Output Voltage Load Current, Over Load Setting, Sensitivity, High/Low cut of voltage, Supply Frequency
Ambient Teemperature 45"C Max, Relative Humidity upto 90%
Output waveform Ture Reproduction Of Input
Overload Capacity 120% Maximum
Type of Cooling Oil / Air
Mode of System Fully automatic
Output Control Contactor Through Manual feather touch button. Optional for automatic (7 Sec to 3 Min)
Servo motor drive AC. Synchronous stepper motor
Inout/Output Connection Up to 6KVA Connectors, above 9 KVA Hylom with bold nut, Above 50KVA Hylam with Al Flat More then 98%
Efficiency   More then 98%
System Construction As Per IS : 9815-1994
Non-Standard Input and Output ranges also available as per customer requirement*
Salient Features
  • Special designs of Transfomer to minimize losses (negligible no load current). More Than 98% effcietly 3-7 Segment LEDs Display
  • Bult-in spike and surge protector
  • All fuctions and parameters are fully software programmable for constant output voltage even with distorted Input from DG set
  • Bult- in Protection Against Under/ Over Voltage (Input/Ouput),Short circuit, single phasing & Phase reverse
  • Sesing circuit is isolated from input
  • All electronic assemblies tested on full load for 48 hours to minimize failures
  • Higher Overload capabilities for high starting and regenerating currents repeated frequently in CNC / Textile machines
  • Auto and manual operation facility. No hunting, No oscillation,No noise generations
  • All components sourced from reputed manufactures
  • Rugged AC synchronise motor with instant Stop / Start Characteristies
  • No effect of power factor
  • In built By-pass Switch upto 30 KVA